American Institute of Aeronautics and Astronauticsīerman B (2012) 3-D printing: the new industrial revolution. In: 24th AIAA applied aerodynamics conference. Ol M Water tunnel velocimetry results for the 1303 UCAV configuration. J Adv Mechan Design Syst Manuf 12:JAMDSM0027. Takato K, Shirayama S (2018) Development of a 3D-printed device evaluating the aerodynamic performance of rotary wings. Rochus P, Plesseria J-Y, Van Elsen M et al (2007) New applications of rapid prototyping and rapid manufacturing (RP/RM) technologies for space instrumentation. American Institute of Aeronautics and Astronautics In: 50th AIAA/ASME/SAE/ASEE joint propulsion conference. Zhang T, Yang HC, Miyamoto CM 3D printing: a cost effective and timely approach to manufacturing of low-thrust engines. Wu H, Li D, Guo N (2009) Fabrication of integral ceramic mold for investment casting of hollow turbine blade based on stereolithography. In: 11th IEEE international conference on control automation (ICCA), pp 694–699 Yu H, Tu Z, Xia X et al (2014) Decentralized adaptive consensus of multi-agent in networks with switching topologies. Sustain Energy Technol Assess 11:186–193. īassett K, Carriveau R, Ting DS-K (2015) 3D printed wind turbines part 1: design considerations and rapid manufacture potential. Guerrero-Villar F, Torres-Jimenez E, Dorado-Vicente R, Jiménez-González JI (2015) Development of vertical wind turbines via FDM prototypes. Tarfaoui M, Nachtane M, Goda I, Qureshi Y, Benyahia H (2020) Additive manufacturing in fighting against novel coronavirus COVID-19. Lin CSH, Chua CK, Yeo JH (2013) Design of high performance badminton shuttlecocks: virtual and rapid prototyping approach. Tarfaoui M, Nachtane M, Goda I, Qureshi Y, Benyahia H (2020) 3D printing to support the shortage in personal protective equipment caused by COVID-19 pandemic. A rapid prototyping application in wind tunnel testing a student project. Kochan A (2003) Rapid prototyping helps Renault F1 Team UK improve championship prospects. īere P, Neamțu C (2014) Design and manufacturing methodology for F1 nose car. Zhou S, Hua XG, Chen ZQ, Chen W (2017) Experimental investigation of correction factor for VIV amplitude of flexible bridges from an aeroelastic model and its 1:1 section model. Giannatsis J, Dedoussis V, Karalekas D (2002) Architectural scale modelling using stereolithography. Residential 3D model wind tunnel pressure testing. Linke B, Garretson I, Jan F, Hafez M (2017) Integrated design, manufacturing and analysis of airfoil and nozzle shapes in an undergraduate course. Seifi H, Rezaee Javan A, Xu S, Zhao Y, Xie YM (2018) Design optimization and additive manufacturing of nodes in gridshell structures. Nachtane M, Tarfaoui M, Goda I, Rouway M (2020) A review on the technologies, design considerations and numerical models of tidal current turbines. Tarfaoui M, Nachtane M, Amry Y, Moumen AE (2018) From renewable to marine energies sources for sustainable development and energy transition in Morocco: current status and scenario. Nachtane M, Tarfaoui M, Hilmi K, Saifaoui D, el Moumen A (2018) Assessment of energy production potential from tidal stream currents in Morocco. Han J, Jung J, Hwang JH (2021) Optimal configuration of a tidal current turbine farm in a shallow channel. Finally, the results showed that 3D printing presents an excellent opportunity in the design and development of tidal energy systems in the future. Therefore, the lowest warpage is observed for PA12-GB. Also, t he warpage of PA12-CB is lower than PEEK-CB by 10.31%, and the warpage of PA12-GB is lower than PEEK-GB by 20.95%. It is concluded that PA12-CB has warpage higher than PA12-GB by 3.78%, and PEEK-CB has warpage lower than PEEK-GB by 8.4%. Once the finite element evaluation has been completed, the deflection, residual stresses, temperature distribution, and the deformed blade or warpage can be obtained. This research examines conceptual considerations of small tidal turbines including material properties and aerodynamic parameters. In this work, the tidal turbine blade is printed by using the selective laser sintering (SLS) method with polyamide 12 (PA12) and polyether ether ketone (PEEK) polymers reinforced by carbon beads (CB) and glass beads (GB). The objective of the paper is to study the thermomechanical performance of 3D printing of a small-scale tidal turbine blade and their process using Digimat-AM because more research efforts are needed in this area. In rural areas and isolated communities, small turbine systems could be locally fabricated and assembled by using additive manufacturing machines and also can be employed to decrease residential energy consumption. The 3D printing technology used for small tidal and wind turbines has great potential to change and overcome certain weaknesses in traditional manufacturing techniques.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |